Critical Knowledge:
VOR navigation is based on your position relative to the station, NOT your aircraft’s heading. This means that your current radial is determined by where you are, not the direction your nose is pointing. To intercept a desired radial, you need to adjust your heading to create an intercept angle, regardless of your current heading.
Step 1: Determine your current position
Using a compass rose we can plot our position on the 320° radial. Ignore the aircraft's heading on the heading indicator. VOR is based on your actual location, not your heading.

After plotting our position, we determine that we are Northwest of the station.
Step 2: Determine the Desired Track
The 010° radial outbound means the aircraft will fly away from the VOR along the 010° radial. This is the desired track.

Step 3: Determine the Direction of Intercept
Turn the OBS knob to show 010° with a FROM indication. The needle swings to the right. Which means you are position wise to the left. If you wanted to intercept the radial you would have to fly right to capture the needle.
I know that this can be the confusing part. Let me try to explain further.
At first when you look at the above picture, it seems that the 010° is to our left. However, position wise, if you were to think of the VOR radials as "spokes on a bicycle wheel", then the 010° radial is greater than the 320° radial and you have to add to get there

Step 4: Calculate the Intercept Heading
The current aircraft's radial is 320°. To intercept the 010° radial outbound, the aircraft must turn toward the radial at the specified intercept angle.

Since the intercept angle is 60°, the intercept heading is calculated as follows:
Intercept Heading=Desired Track−Intercept Angle
Intercept Heading=100°+060°=070°
...
...
...
Here are the practical steps in the airplane:
First turn the OBS to your desired radial of 010°

Turn to your intercept heading towards the needle.

Once the needle is centered, it means that you are on your desired radial.

Then turn the aircraft to head in the same direction of your desired radial.

Critical Knowledge:
VOR navigation is based on your position relative to the station, NOT your aircraft’s heading. This means that your current radial is determined by where you are, not the direction your nose is pointing. To intercept a desired radial, you need to adjust your heading to create an intercept angle, regardless of your current heading.
Step 1: Determine your current position
Using a compass rose we can plot our position on the 320° radial. Ignore the aircraft's heading on the heading indicator. VOR is based on your actual location, not your heading.

After plotting our position, we determine that we are Northwest of the station.
Step 2: Determine the Desired Track
The 010° radial outbound means the aircraft will fly away from the VOR along the 010° radial. This is the desired track.

Step 3: Determine the Direction of Intercept
Turn the OBS knob to show 010° with a FROM indication. The needle swings to the right. Which means you are position wise to the left. If you wanted to intercept the radial you would have to fly right to capture the needle.
I know that this can be the confusing part. Let me try to explain further.
At first when you look at the above picture, it seems that the 010° is to our left. However, position wise, if you were to think of the VOR radials as "spokes on a bicycle wheel", then the 010° radial is greater than the 320° radial and you have to add to get there

Step 4: Calculate the Intercept Heading
The current aircraft's radial is 320°. To intercept the 010° radial outbound, the aircraft must turn toward the radial at the specified intercept angle.

Since the intercept angle is 60°, the intercept heading is calculated as follows:
Intercept Heading=Desired Track−Intercept Angle
Intercept Heading=100°+060°=070°
...
...
...
Here are the practical steps in the airplane:
First turn the OBS to your desired radial of 010°

Turn to your intercept heading towards the needle.

Once the needle is centered, it means that you are on your desired radial.

Then turn the aircraft to head in the same direction of your desired radial.
