Reference From the Ground Up 7.4
Lambert Conformal Conic — Useful for long distances because a straight line on the map is very close to a great circle course. Most VFR charts are Lambert Conformal Conic.
Mercator — The most commonly used projection for navigating in small areas because of its accuracy and the fact that a straight line is also a rhumbline.
Lambert Conformal Conic
The angles between meridians and parallels will be the same on the chart as they are on the ground. The VFR Navigation Charts (VNC Series) and the World Aeronautical Charts (WAC Series) are based on Lambert Conformal Conic Projections.
The properties of the Lambert Projection are:
Meridians are curves or straight lines converging towards the nearer pole.
Parallels of latitude are curves which are con-cave towards the nearer pole.
A straight line drawn between any two points on the map represent an arc of a great circle.
A straight line, or great circle route, cannot be flown without changing heading at regular intervals. It is necessary to change heading 2° for every 3° of longitude.
Mercator
Meridians are straight and parallel lines, Parallels of latitude are straight and parallel lines. A straight line drawn between any two points on the chart will represent a rhumb line.
Transverse Mercator
The Transverse Mercator Projection, is quite accurate in depicting scale, especially on charts covering a relatively small geographical area.
The VFR Terminal Area Charts (VTA Series) are based on Transverse Mercator Projections.
Chart scales
World Aeronautical Chart scale is 1:1,000,000 (1 inch to 16 miles). are based on the Lambert Conformal Conic Projection and conform to the characteristics of that projection.
The VNC chart scale is 1:500,000 (1 inch to 8 miles). VFR Navigation Charts are based on the Lambert Conformal Conic Projection and conform to the characteristics of that projection.
VFR Terminal Area Charts scale is 1:250,000 (1 in to 3.43 NM). VFR Terminal Area Charts are based on the Transverse Mercator Projection.
Reference From the Ground Up 7.4
Lambert Conformal Conic — Useful for long distances because a straight line on the map is very close to a great circle course. Most VFR charts are Lambert Conformal Conic.
Mercator — The most commonly used projection for navigating in small areas because of its accuracy and the fact that a straight line is also a rhumbline.
Lambert Conformal Conic
The angles between meridians and parallels will be the same on the chart as they are on the ground. The VFR Navigation Charts (VNC Series) and the World Aeronautical Charts (WAC Series) are based on Lambert Conformal Conic Projections.
The properties of the Lambert Projection are:
Meridians are curves or straight lines converging towards the nearer pole.
Parallels of latitude are curves which are con-cave towards the nearer pole.
A straight line drawn between any two points on the map represent an arc of a great circle.
A straight line, or great circle route, cannot be flown without changing heading at regular intervals. It is necessary to change heading 2° for every 3° of longitude.
Mercator
Meridians are straight and parallel lines, Parallels of latitude are straight and parallel lines. A straight line drawn between any two points on the chart will represent a rhumb line.
Transverse Mercator
The Transverse Mercator Projection, is quite accurate in depicting scale, especially on charts covering a relatively small geographical area.
The VFR Terminal Area Charts (VTA Series) are based on Transverse Mercator Projections.
Chart scales
World Aeronautical Chart scale is 1:1,000,000 (1 inch to 16 miles). are based on the Lambert Conformal Conic Projection and conform to the characteristics of that projection.
The VNC chart scale is 1:500,000 (1 inch to 8 miles). VFR Navigation Charts are based on the Lambert Conformal Conic Projection and conform to the characteristics of that projection.
VFR Terminal Area Charts scale is 1:250,000 (1 in to 3.43 NM). VFR Terminal Area Charts are based on the Transverse Mercator Projection.